You are correct that when the Curt Trailer Hitch Receiver Class I # C11367 is installed, it will move the steel bumper closer to the bumper fascia by the width of the mounting bracket. However, this will not negatively impact or deform the bumper fascia.
If installing the hitch caused problems at the bumper fascia, the manufacturer would state that the hitch requires trimming of the bumper fascia or they would not list the hitch as a fit for the vehicle. The # C11367 requires no trimming... view full answer...
The difference between a 2000 Toyota Tundra with a towable bumper and a non-towable bumper is that the model with the towable bumper will have a cutout in the center of the bumper for a hitch ball wheres the model with the non-towable bumper will not have a cutout in the center of the bumper for a hitch ball.
The trailer hitch receiver I recommend for your Tundra is the Curt Trailer Hitch Receiver part # 13184 because it will fit models both with the towable bumper and models with the... view full answer...
I am unfamiliar with the Barden Bumper and in my research, I could not find any specific information regarding the Barden Bumper. Our trailer hitches are not tested with aftermarket bumpers.
We have two bumpers that have been determined to be a fit for your truck with a factory bumper. The # BWHDRH25122 is for standard and step bumpers and the # BWHDRH25198 is for deep drop bumpers. I recommend measuring from your frame to the bottom of your bumper to know how much distance you will need... view full answer...
The Curt RV Bumper Hitch # C19101 you mentioned is designed to fit 2" x 4" RV bumpers, and will unfortunately not fit your 4" x 4" bumper.
Instead, you're going to want to use the Curt RV Bumper 2" Trailer Hitch Receiver # E-100 which will fit your 4" x 4" RV bumper. view full answer...
If the ranch hand bumper is the same thing as a cowboy bumper or deep drop bumper then none of the hitches for the 2006 Dodge Ram 2500 are confirmed to fit because they are not tested on truck models with alternate bumpers. You would have to put the old bumper back on.
If the factory hitch is the one welded to the frame then you would need # C15809 if you did install the factory bumper. This hitch fits below the factory hitch. I have linked instructions and a video showing installation... view full answer...
As long as you have full access to the underside of the bumper mounting holes, through the step bumper, and they measure 8-3/4 inches center to center then you may be able to mount the Curt bumper mount hitch # E-3S without removing the step bumper.
However, when speaking with my contact at Curt, they mentioned this type of hitch is meant for RV's. He also confirmed that in most cases, the factory bumpers would not fit this hitch.
The length of the bolts that are included with the... view full answer...
Unless the vehicle manufacturer includes a hitch cut out on all the trim levels of a vehicle, the aftermarket hitches will usually either sit below the rear bumper, or require to trim or notch the rear bumper to allow for hitch installation.
We do not carry any hitches that will fit behind the rear bumper of a 2008 Honda Odyssey. You will be able to see the hitch, but it does not stick out beyond the rear bumper. I have added a link below to the instructions for Draw-Tite part # 75270.... view full answer...
The RV Bumper 2" Trailer Hitch Receiver - Clamp-On # S64025 is designed for the standard 4 inch RV bumper, but it will fit 4 inch to 4.5 inch continuous welded steel bumpers. The mounting plate measures 6 x 6 inches. This hitch receiver is not to be used with adapters or extenders. view full answer...
The Curt hitch part # C14006 does fit your 2018 Chevy Silverado 1500 and does fit below the rear bumper support. I attached a picture that shows it installed on a truck like yours and you can see the bumper beam is still intact.
I also attached an install video for this hitch for you to check out as well. view full answer...
A deep drop bumper is a bumper that hangs further below the frame than a standard bumper. Check out the photo that I attached showing a deep drop bumper compared to a standard bumper and a step bumper.
We have three frame mount trailer hitches that will work with a deep drop bumper on your 1987 Chevrolet C/K 1500. You could install the Curt Hitch, # C13099 or the Draw-Tite Hitch, # 41504. These are all Class III trailer hitches that have a towing capacity of 5,000 lbs and a tongue weight... view full answer...
The Curt Bumper Hitch, part # E-3S, is made to attach to a truck step bumper. It is a universal fit design so it is not listed for a specific vehicle. The mounting holes are 8-1/2 inches center to center between the holes.
If your 2007 Toyota Tacoma has a step bumper and has mounting holes with the 8-1/2 inch dimension then it will bolt to your bumper. If you do not have holes that will line up with the hitch then you can still use the hitch but you would have to drill new holes. I am... view full answer...
From what I could find, the Southern Comfort package on a 2005 Chevy Silverado did not affect the bumper. What you can do to determine if the CURT Bumper Mount Trailer Hitch, # E-3S, will fit is to measure the area of the bumper where the hitch will install and compare that to the dimensions of the hitch.
The top flat part of the hitch is 11 inches by 4 inches. The bolt holes closest to the receiver opening are 8-3/4 inches apart on center. The other set of bolt holes is 6 inches apart... view full answer...
If you 2000 GMC Jimmy has a rear step bumper and the mounting hole spacing is 8-3/4 inches on center then the Curt 2 inch Bumper Hitch, item # E-3S, will work on your vehicle. The towing capacity of the hitch will be the lowest rated item in the system which are the vehicle, bumper or hitch itself, whichever is lowest. You can find the towing capacity either in your owners manual and/or on the bumper itself.
The Curt 2 inch Bumper Hitch comes with all of the mounting hardware and instructions... view full answer...
Aftermarket bumpers are different sizes and shapes compared to the factory bumpers so the hitches we offer like the part # C15803 are designed to fit and clear the factory bumpers but since the aftermarket bumpers are a different size there's not easy way to tell if the hitch would also fit with it and not interfere. view full answer...
The Curt RV Bumper 2" Trailer Hitch Receiver # E-100 is a universal hitch fit that can be installed on your 2022 Grand Design Imagine XLS Travel Trailer as long as it has a 4"x4" bumper. While this hitch does have a 350 lb weight rating, if your bumper isn't rated for very much weight then it is still possible to overload your bumper even if you haven't gotten close to the weight rating of the hitch so it's best to check the weight rating for your bumper as well.
If the weight of the rack... view full answer...
The Draw-Tite hitch part # 76026 requires the removal of the bumper beam on the 2019 Jaguar F-Pace because the hitch basically takes the place of the bumper beam. The design of the Draw-Tite hitch does not allow the bumper beam to bolt back on with the hitch installed because the Draw-Tite hitch is a bit longer. The Curt Class III Hitch design part # C13291 has a shorter rounded design which allows the bumper beam to fit over it. view full answer...
I have a solution for you, but the Ultra-Fab 2" Motor Home Trailer Hitch Receiver part # UF35-946401 will only fit bumpers up to 4" x 4" .
For your 4-1/4" x 4" bumper, I recommend the Buyers Products RV Bumper Receiver Hitch item # 337RVA24. The u-bolts will actually fit bumpers up to 4-1/2" wide so your 4-1/4" wide bumper won't be an issue. The fit will be tight enough that you would not have any play.
It's perfect for a bike rack, cargo carrier, or any other cargo accessory. Keep... view full answer...
The Westin Perfect Match Series Rear Step Bumper - Black Powder Coated Steel # 32018 is built to OEM specifications to perfectly match your 2003 Toyota Tacoma. It has a pre-drilled 3/4" hole for a hitch ball to mounted, which is what the OEM bumper has; this bumper can tow up to 3,000lbs when a hitch ball is added. For a hitch ball you can use 2" Hitch Ball - 3/4" Diameter 3,500 lbs # 19258.
If you are referring to the actual trailer hitch receiver, then that is mounted to the frame of... view full answer...
The only solution really is a new trailer hitch receiver because the Swagman RV Bumper 2" Trailer Hitch Receiver # S64025 is a clamp-on designed only to be mounted above the the bumper and doing otherwise compromises the safety and integrity of both the hitch and your RV.
There are bumper mounted hitch receivers that will accommodate 2 inch bike racks, which is what the Swagman was designed to do. The Buyers Products RV Universal Receiver Hitch # 3371804060 has a 2" receiver and as you... view full answer...
I can help you find the highest rated weight capacity hitch for the 1993 Ford F-150 Flareside. The F-150 of that year had two bumper styles, standard step bumper or deep drop bumper.
Most likely the Ford Flareside has a standard step bumper. For the standard bumper, I recommend Curt Class V receiver part # C15300. The Curt hitch fits standard bumpers and offers up to 16,000 lbs of towing capacity. It is a custom fit trailer hitch does require some drilling of the frame. There are not... view full answer...
Go To Results